How to correctly operate the rigid box making machine and debugging methods

How to correctly operate a rigid box making machine

1. Choose a flat table for the rigid box-making machine, place the machine steadily, and pull the chassis legs apart to make the machine panel easier to observe.

2. Insert one end of the power cord into the socket on the rear panel of the chassis, and the other end into the power supply socket. Be sure to use a single-phase three-wire power supply.

3. Turn on the "POWER SW." on the rear panel of the chassis, press the "SWITCHING" button on the panel, and wait until the "WARM UP" green indicator light turns on, and the machine can work.

4. Press and hold the "SETTING BUTTON" button to set the appropriate value, usually between 0.5-2.0 seconds.

5. Insert the plug on the handheld sensor head into the socket on the panel and tighten it, paying attention to the positioning gap.

6. Place the sensor head on the container cover and press the start button on the handle. At this time, the "HEATING" red indicator light will light up, indicating that it is heating. Do not move the sensor head away. The "HEATING" red indicator light will turn on. After it goes out, remove the sensor head and wait for the green indicator light of "WARM UP" to light up or the buzzer inside the machine to give a short "beep" prompt before proceeding with the sealing operation of the next container.

7. Check the sealing quality of the top and bottom lid carton forming machine. According to different materials, container diameters, and production efficiency, appropriately adjust the "SETTING BUTTON" button to achieve the best sealing quality.

Summarize:How to operate the rigid box making machine: Choose a flat workbench, insert one end of the power cord into the socket on the rear panel of the chassis, and the other end into the power socket, press and hold the "SETTING BUTTON" button to set the appropriate value, and turn on the "power switch" Insert the plug on the handheld sensing head into the socket on the panel and tighten. Place the sensor head on the container lid and press the start button on the handle.

Adjustment method of rigid box-making machine

After the installation of the rigid box-making machine is completed, first debug and produce the machine, turn on the power, turn on the power switch on the control panel, and the emergency stop switch button, and check whether the parameters of the rigid box-making machine display screen are normal.

Connect the air source and adjust to 0.6-0.8kg/cm2.

Adjustment of the size of the packaging box: mainly adjust the carton frame, the box transport chain, the size of the box frame, and the length, width, and height of the box transport chain according to the size of the carton.

1. Place the carton we want to adjust on the box base, and then adjust the guides of the box base close to each side of the box. Make sure the box is stable and does not fall.

2. Adjust the length of the carton: Place the sealed carton on the box-out conveyor belt, and then adjust the handwheel on the right so that the rigid box-making machine conveyor belt is in contact with the edge of the carton.

3. Carton width adjustment: First loosen the two sprocket screws outside the main chain. Then place a cardboard box in the middle of the chain and adjust the width of the chain to be the same as the width of the box. Then tighten the rear sprocket screw.

4. Carton height adjustment: Loosen the two fastening screws at the front and rear of the upper guide rail, and then turn the upper handwheel to make the upper guide rail contact the top of the carton and the guide rail. Then tighten the set screw.

5. Adjust the size of the feeding grid: Unscrew the fixed bearing screw, place the product in the pushing plate grid, push the baffle left and right until it is adjusted to the appropriate size, and then tighten the screws. (Note: There are several screw holes on the panel here. Be careful not to tighten the wrong screws when adjusting the machine).

After the adjustment of each part is completed, you can start to activate the inching switch on the control panel and use the inching operation to perform manual debugging such as box opening, box suction, feeding, corner folding, and glue spraying. After the debugging of each action is completed, the start button can be turned on, and finally, the materials can be placed to start normal production.

Leave professional matters to professionals. When purchasing an automatic rigid box-making machine, choose Zhengrun Packaging Equipment. It is a professional brand that started the packaging equipment business in China. It is engaged in the research and development, design, production, and sales of box making equipment.